Story Sales & Service

Patz

Tapered-bore drive pulley mounts to a 1-1/8-inch (29 mm) drive shaft with a greaseable flange bearing at the top of the drive tube
Easy access to oil reservoir
High-volume delivery
Protection against bearing contamination
Bearing seals can be purged every 8 hours thanks to a grease line from the seal pack to the top of the pump
Clogging prevented and positive input provided
Shear plate has two legs to help support pump off the floor of the pit
Impeller transition area features beefed-up steel for long life
Pump available in various lengths to fit pit depths of 3 12 feet

Pumping capacity up to 1,580 gals./min
Available in lengths to fit your application: 6 ft. (1.8 m), 8 ft. (2.4 m), 10 ft. (3.0 m), and 12 ft. (3.6 m)
A 16-inch (40.6 cm) Impeller for added capacity
Variable agitation capacities with a standard dual agitation system
Abrasion-resistant steel in high wear areas for longer life.
Tapered-bore drive pulley mounts to a 1-3/4 inch (44.5 mm) drive shaft with a greaseable flange bearing at the top of the drive tube
Easy access to oil reservoir
Lifting loops located on top of the pump allows easy insertion and removal of the unit from the pit with a tractor loader, skid-steer loader or winch
A steel mounting plate is included as standard equipment to allow precise positioning of the pump to match the pit depth. Plate can be lagged to a concrete pad or curb
Pump available in various lengths to fit pit depths of 5 ft. 6 in. (1.7 m) to 12 ft 10 in. (3.9 m).

Stationary base secured to manure pit or two-point tractor hitch with hydraulics for tilting
Match your pit depth with choice of four pump lengths: 6, 8, 10 and 12 feet (1.83, 2.44, 3.05 and 3.66 m)
Large U-bolts allow the frame to be adjusted up or down for precise placement
Match your desired speed of transfer and loading with two pump sizes: 6-inch (152 mm) and 8-inch (203 mm) pipe
Reduce agitation time with dual nozzles that blend crusted manure and settled solids into a liquid slurry fast
Get better pit clean out by agitating every corner with adjustable nozzles (rotate both horizontally and vertically)
Remove clumps of straw with chopping action over impeller shredder plate
Lower repair costs with impeller housing of abrasion-resistant steel in high-wear areas
Tractor Requirement: 100 HP minimum

A stationary base secured to manure pit is standard on the 6000E Pump
Equipped with a two-point tractor hitch for easy insertion and removal from pit for service
Match your pit depth with choice of four pump lengths: 6, 8, 10 and 12 feet (1.83, 2.44, 3.05 and 3.66 m)
Large U-bolts allow the frame to be adjusted up or down for precise placement
Get better pit clean-out by agitating with a nozzle which can be rotated horizontally
Save time when agitating, transferring, and loading due to swept-back impeller blades for high-volume pumping up to 2,500 gallons per minute-during agitation and 2200 gallons per minute during loading
Horsepower Requirements: Twin 15, 20, 25, or 30 HP, 3-phase motors.

Pump: 1/2 hp. 1625 RPM: Single phase; 230 volts; 5.8 amps; 84 lb. (38 kg); maximum solids diameter: 2" (50.8 mm); two-vane, non-clogging impellers
Pump Performance: G.P.M. at total head in feet
Gutter Widths: 15" to 20"
Hole Size for Installation: 18" (457 mm) wide x 24" (610 mm) long x 30" (762 mm) depth below gutter bottom (20 gal. sump)
Pipe Size: 2" (50.8 mm) PVC schedule 40 Pipe supports should be every 10' (3m) apart
Height to top of handle: 19-3/8"
Width at widest point: 12-5/8"
Discharge: 2 NPT
Suction inlet opening: 2"
Weight: 84 lb.